Hardwood Sand & Refinish
Bring tired hardwood floors back to life with a full sand, stain, and refinish — dust-contained sanding, hand-cut edges, durable finishes.
- Veteran-Owned & Operated
- Licensed & Insured
- In-House Crews — No Subcontractors
Built for Buildings That
Can't Slow Down.
Most hardwood floors that look worn out aren't worn out — they just need a proper sand and refinish. ValorCraft uses drum and orbital drum sanders with dust-containment systems, hand-cuts every edge and corner so the field sanding matches all the way to the baseboard, and applies finish in multiple coats with light screening between passes. Whether you're matching a stain across a room addition, going lighter to update a dated color, or taking the floor back to bare wood, the process starts with reading what the existing floor actually has left in the wear layer — and being honest with you about what's possible.
- Dust-contained drum and random-orbit sanding — not a shopvac hooked to a floor buffer
- Edge sanding by hand on all four walls so machine marks don't show at the baseboard
- Multiple finish coats screened between passes for adhesion and a flat, even sheen
- Stain samples applied and approved before committing the whole floor
Full Commercial Scope —
Demo To Punch List.
One contract, one crew. Substrate prep, install, transitions, and base — everything that touches the floor stays under our scope.
Full Sand & Refinish
Drum or orbital drum sand to bare wood in the field, edger at walls and corners, hand-scraping in closets and under radiators — followed by stain and multiple topcoats.
Screen & Recoat
Light abrasion of the existing finish coat, dust removal, and fresh topcoat applied over the current stain — for floors that have lost their sheen but still have a solid wear layer.
Stain Application
Oil-based or water-based stain wiped, buffed, and tacked between sand and topcoat — with sample boards applied to the actual floor for approval before the full application.
Oil-Based Polyurethane Finish
Traditional oil-based poly in satin, semi-gloss, or gloss — durable, amber-toned, and forgiving on older floors where the wear layer is thinner.
Water-Based Polyurethane Finish
Water-based urethane for a clear, non-yellowing finish that dries faster and allows same-day re-coat — good for maple, ash, and any floor where color clarity matters.
Hardwax Oil & Natural Finishes
Penetrating oil and hardwax oil finishes for homeowners who want a matte, low-sheen look that's field-repairable without a full sand — we discuss tradeoffs before you commit.
Board Repair & Replacement
Damaged, cupped, or split boards replaced before the sand — matched to the existing species and width, and blended so the repair doesn't read as a patch after finish.
The Commercial Standard
PMs Keep Calling Back.
Veteran-owned discipline applied to commercial flooring — clean schedules, accurate scopes, and crews that close out the punch list the first time.
Honest Wear-Layer Assessment
We check the existing finish depth and gauge the board thickness before we price the job. If the floor doesn't have enough wear layer left, we tell you before we start — not after we've sanded through.
Dust Containment That Works
Commercial dust-containment systems on the drum sander pull the dust at the source. You'll still want to cover electronics and clean after — but you won't be finding sanding dust in your closets for weeks.
Edge Work That Matches the Field
The difference between a professional refinish and a rental-machine job shows at the walls. We hand-cut edges so the swirl pattern and depth match the drum sand all the way to the baseboard.
Stain Samples Before Commitment
We apply two or three stain options to a corner of the actual floor — not a sample board — so you see how the color reads on your specific species and grain before we commit to the whole room.
Veteran-Owned Scheduling Discipline
Refinish work requires the house to be empty and humidity controlled for curing — we build that into the timeline and communicate clearly so your move-back plan isn't a guess.
Stair Coordination Available
We can coordinate the stair refinish as part of the same schedule — sanding landings and existing treads to match the field so the stain and sheen are consistent floor to stair.
Five Steps. No Surprises.
Schedules That Hold.
The same process whether it's one suite or one hundred — clear scope, clean prep, phased installs, and a closed punch list.
- 01
Floor Assessment
We inspect the existing finish, check board moisture content, identify damaged boards, and assess how many sanding passes the wear layer will support before pricing the job.
- 02
Prep & Furniture Clear
Existing furniture out of scope (your responsibility unless quoted otherwise), base shoe removed where needed, and protruding fasteners set flush so they don't tear the sanding belt.
- 03
Sand — Field, Edge, Detail
Drum or orbital drum in the field, edger at walls, and hand scraper or detail sander in corners, closets, and any area the machines can't reach — progressively finer grits to the final sand.
- 04
Stain (If Applicable)
Stain applied by the approved color, wiped to an even tone, and allowed to dry fully before topcoat — floor tack-checked before any finish is opened.
- 05
Finish Coats & Cure
Minimum two to three coats of finish, screened between passes, with cure time communicated upfront so you know exactly when light foot traffic and full furniture load are safe.
Answers
Before You Ask.
How do I know if my floors can be refinished?
Solid hardwood typically supports three to five refinishes over its lifetime depending on original thickness and prior sanding depth. Engineered hardwood depends on the wear layer — we measure with a gauge during the site walk and tell you honestly how much life is left.
How long do we need to be out of the house?
For a full sand and oil-based finish, plan for two to three days minimum — typically longer if you have pets or sensitivity to finish odors. Water-based finishes dry faster and have lower VOC, reducing that to one to two days in most cases. We confirm the timeline in writing before we start.
Can you match my existing stain color?
We can get close on most standard colors. Exact matches depend on the species, the age of the existing stain, and whether the previous product is still available. We apply samples to your actual floor so you can see the result before we commit — we don't promise a match we can't deliver.
Is oil-based or water-based finish better?
Both are durable when applied correctly. Oil-based poly adds a warm amber tone, dries slower, and is more forgiving on older floors. Water-based cures faster, stays clear, and has lower odor — but requires more coats and better prep. We'll recommend based on your species, existing tone, and scheduling needs.
Will sanding remove scratches and pet stains?
Surface scratches yes — deep scratches and pet urine stains that have penetrated into the wood fiber are harder. We identify gray or black staining during assessment and discuss options: oxalic acid treatment, board replacement, or accepting that some character marks may remain after refinish.
Do you refinish stairs as well?
Yes. Stair sanding and refinishing can be coordinated as part of the same schedule — landing, treads, and risers sanded and finished to match the field. We sequence the stair work so it's done last and you're walking on a cured surface before we close out.
Serving the
Piedmont Triad, NC.
ValorCraft Flooring proudly installs residential and commercial flooring across the Piedmont Triad and surrounding North Carolina communities.
Schedule In Your Area- 01High Point
- 02Greensboro
- 03Winston-Salem
- 04Lexington
- 05Kernersville
- 06Thomasville
- & surrounding Triad areas
Ready to Upgrade Your Floors?
From first estimate to final walkthrough, ValorCraft Flooring delivers professional flooring built to last.
(336) 596-7835 · valorcraftflooring@gmail.com